|
|
New
for the download |
VNDNET
client
application
(6,0 MB) |
|
 |
LTE
router with one POTS telephone line interface, battery backup,
serial data interface, LAN Port and WLAN access point |
 |
- 4G
LTE/UMTS/GSM router for lift application
- 4G/3G/2G
mobile connection with SIM of any operator
- WLAN
access point
- Dynamic
DNS client
- Serial
data transmission with RS-232, RS485 and CAN-bus interfaces
- 1
LAN port 10/100 MB (RJ45 connector)
- 1
voice port FXS for emergency phone
- 2
multi-function programmable relays
- Integrated
battery backup
|
The
ultimate way to upgrade your existing equipment for condition
monitoring and predictive maintenance: with only one SIM card
the 4G.Router allows to manage Voice and Data transmission, vocal
calls and Internet
services simultaneously, remote monitoring via LAN and WLAN connectivity.
Thanks to the connection to the VNDNet freeware platform, 4G.Router
manages the remote control of devices connected to the serial
port (RS-232/485/CANBus) or to the LAN port via DDNS service.
4G.Router
provides also a POTS analogue teleophone line, up to 9 ECII or
Helpy emergency call system units can be connected to one router.
The router is delivered with a LTE antenna, a WLAN antenna and
a PSU. It is powered with a 230 Vac mains, or using a 11 to 26
Vdc voltage. An emergency power supply with battery backup is
integrated in the unit. The battery is tested periodically and
an alarm is send using the emergency phone or an SMS if the battery
fails the test.
|

4G
router VNDNet application example
|
Standard
features
- Voice
calls
- Access
point wireless (to offer WLAN connectivity to connected devices)
- Dynamic
DNS client (to allow the user to remotely access, using the
public Internet, the router itself and all the devices connected
to it)
-
2 technological alarm inputs (notification via SMS or CLI call)
-
2 relè outputs (local activation or via SMS)
-
Data transmission (RS-232, RS-485 and CAN-bus standards)
- Local
programming via telephone (DTMF tones)
- Remote
programming via SMS
- Reading
of programming codes via SMS
-
Caller number display service
-
CLIP / CLIR
-
Roaming service management
-
Battery check (low/dead/replaced battery notification via SMS,
ECII or Helpy emergency phone)
- External
power failure control (failure/restore notification via SMS)
-
Relay-based notification of external power failure
-
Relay-based notification of 4G LTE / UMTS / GSM network loss
-
Signal level check via local telephone or via SMS
-
Automatic converter of selected telephone number
-
Programmable telephone line voltage
-
Adjustable reception and transmission levels
-
Customizable timeout of post dialing
-
Automatic country setting
-
Automatic reboot under prolonged 4G LTE / UMTS / GSM signal
absence
-
Remote reboot
-
Firmware update OTA
-
Compatible with software VNDNET PC client, specifically designed
for data transmission management
-
Allows to send SMS via serial port RS232 and CANBus
-
Remote monitoring independently from proprietary protocols
-
Cost reduction and data transmission service via server cloud
for M2M services
- Incoming
text messages transmission towards devices wired in the DB9
connector (under RS232 standard)
-
High transmission speed
-
Low consumption
-
Easy installation by connectors and/or terminal blocks
|
Technical
data
- Module:
LTE cat. 1 Penta-Band / UMTS HSPA Dual-Band / GSM Dual-Band
-
Frequencies: LTE (700/800/900/1800/2100 MHz) / UMTS HSPA (900/2100
MHz) / GSM (900/1800 MHz)
-
4G LTE / UMTS / GSM signal indicator LED: green
-
4G LTE / UMTS / GSM signal indicator flash: 1, 2, 3 or 4 for
low, medium, good, high signal level
-
Device status indicator LED: red
-
Line status indicator LED (FXS output: clear, engaged, ring):
white
-
Data transmission indicator LED: yellow
-
Power supply status indicator LED: blue
-
SIM card slot: 2FF
-
Relay output: NO (24 V 1 A)
-
Terminal blocks for data transmission in RS-232, RS-485 and
CAN-bus standard
-
Telephone line connection: terminal block
-
Micro USB A/B port for pc connection
-
Antenna connectors: SMA/f
-
Antenna: magnetic base antenna with cable (2 m) and SMA/m connector
-
Antenna: magnetic base antenna with cable (2 m) and SMA/m connector
for diversity antenna in LTE reception (optional)
- WIFI
stylus antenna
- Power
supply: from 11 V to 26 V (dc)
-
Power supply input: terminal block 12/24 Vdc / jack for 230
Vac external adapter
-
Back up battery: NiMH 800 mAh 7,2 V
-
Expected operation time with a new battery in idle state: 8
hours
-
Expected operation time with a new battery in conversation state:
2 hours
-
External adapter: 100-240 Vac 50-60 Hz input / 12 Vdc 500 mA
output / UK / CE mark
- Dimensions
(antenna not included): 95x95x30 mm
-
Weight: 273 g
|
|