Lift emergency call system for GSM wireless networks

• Easy programming
• Calling ID with CPC procedure
• Integrated battery backup
• Certified EN 81:28 compliance
• Intercom function between cabin and machine room

The EC II SE GSM is activated using the existing or new installed alarm button. In case of an emergency the button is pressed for a duration of 5 seconds and an emergency call will be setup. The call can be linked to a call center or a normal phone.

On the backside of the speakerphone unit there is a keypad which is used to program the telephone numbers, the features and to test the device. Furthermore the unit can be programmed remotely using a programming software or SMS.

If necessary the trapped person can be called also from outside. This feature is normally active, but can be deactivated or activated only after an emergency call was set.

The EC II SE GSM has an integrated battery backup system, which can be also used to power an emergency light. For the intercom function between the lift cabin and the machine room a normal analogue telephone can be connected to the controller unit. An external loop antenna amplifier for hearing aid can also be connected to the device.

EC II SE GSM
AP/UP speakerphone for flush or surface mounted installation

Standard features

• One emergency call button (breaker or closer) can be connected, integrated with ALBU version
• Up to six 20 digits long telephone numbers can be stored
• Skip to the next stored number if no answer or no acknowledge
• Call forward to the next programmed number from the call receiver
• 2 programmable ID codes up to 10 digits long
• Programming using build in keypad, external Modem or SMS
• Programmable automatic call answer (()n/Off, only during alarm state)
• High-end speakerphone
• Duplex/simplex switch using DTMF codes
• Call disconnect using a DTMF code
• Optical (EN 81:70) and acoustic indicators for status and connection
• Programmable test alarm setup between 1 and 9 days
• Calling party identification using CPC protocol or SMS
• Integrated battery backup for emergency phone, emergency light and horn
• Connection to an external loop antenna amplifier
• Alarm filtering function
• Alarm log readable using SMS functionality
• Intercom function between cabin and machine room
• GSM signal quality readout and log readable using SMS functionality
• Battery test procedure with automatic battery failure alarm
• Alarm signal input for alarm call to call center or SMS receiver
• Driver contact output activated by DTMF dial
• End-of-alarm signalling conform to EN 81:28 with integrated reed contact or alarm input
• Remote software upgradeable
• Complete, semplified or no acknowledge procedure

Optional features

• External alarm button with integrated microphone for installation on the top/bottom of the lift cabin
• Intercomphone for machine room
• Pit phone

Technical data

• Power supply: 230 Vac, 0,1 A
• Environment: + 5° to + 40° C, 90% humidity (not condensing)
• Dimensions:
  • 185 x 200 x 75 mm (L x H x D), 1780 g ca. controller unit
  • 125 x 180 x 23 mm (L x H x D), 280 g ca. ALBU speakerphone
  • 100 x 100 x 23 mm (L x H x D), 280 g ca. AP/UP speakerphone
  • 90 x 104,5 x 26 mm (L x H x D), 250 g ca. BG speakerphone
• Casing: stainless steel 1,5 mm vandal proofed plate (AP/UP, ALBU) or aluminium casing (BG), 1,5 mm aluminum case for controller unit
• Alarm buttons: one main button in the cabin, two slave button with microphone for
  installation on top/bottom of the cabin
• Battery backup: integrated maintenance free battery 12 V 2 Ah
• Indicators: three LEDs in the controller unit, optical (2 LEDs) and acoustic indicators in the speakerphone unit
• Antenna: external 50 Ohm
• GSM network: dual band 900/1800 MHz
• Installation: one controller unit on the cabin roof or machine room (max. 25 m distance), one speakerphone inside the cabin
• Alarm receiver: Telelarm VIS, Attendo Wilma, Eurofunk, Netcom, Alec, DTMF phones, mobile phones
• Protocol: CPC, P100
• Signalling: DTMF tones
• Approvals: CE, EN81:28